|
| One 40 uF and 3 20 uF at 525V sections. Twist-lock mount, 1 3/8 inch (35mm) diameter by 2 1/2 inches (65mm) long. Fits Dynaco ST70, Mk2, Mk4, Scott 299, LK48, LK72 and many other tube amps.Not recommended for use in Dynaco Mk3 or Sunn amps,which really need a 550V or higher rating...(use an SDS Labs capacitor board instead for reliable service).. Fresh new stock made in USA. |
|
|
|
Four 20 uF at 475V sections. Twist-lock mount, 1 3/8 inch (35mm) diameter by 2 inches (52mm) long. Perfect fit for Dynaco PAS2 and PAS3, also Fender Champ, many others. Fresh new stock made in USA. |
|
|
| Replacement sets of speaker terminal strips for dynaco amplifiers. Price includes two terminal strips. |
|
|
| Bias Repair Set for Dynaco ST70 & Mk4.Replaces selenium bias rectifier with silicon diode,
also includes resistors & capacitors used in bias circuit
that are not on the printed circuit board.Not needed on ST70 if you install the SDS Labs Capacitor board |
|
|
| Bias Repair Set for Mark 3Replaces selenium bias rectifier with silicon diode,
also includes resistors & capacitors used in bias circuit
that are not on the printed circuit board.These parts are also included in the Dual Bias Kit on this page.One set required per amplifier |
|
|
| Dual Bias Kit for Dynaco Mk3/Mk2 Amplifiers with Triode Electronics upgradeThis allows for biasing each 6550/KT88/EL34 tube
individually rather than as a pair, note that a hole
must be drilled for an additional bias control to use this.
Kit includes parts that are in the regular Bias Repair kit as well.This kit works only with our board. One kit required per amplifier |
|
|
| ST70 Offboard Resistor SetThis set includes all resistors in the amplifier that are not mounted on the circuit board. Includes 10ohm 2W biaset resistors, 10k 2W bias supply resistors, 1k 1/2W grid stoppers, 6.8k 2W & 22k 2W power supply resistors, and 470k 1/2W input grid reference resistors. |
|
|
| 15ohm 2W Carbon Film Resistor. Made by Piher in Spain. Great replacement for Original ST70 Biaset resistors to keep the 1.56V biaset. Note, these are sold in a quantity of one so if you are using them for a ST70 you will need to order two of them. |
|
|
| Fits 3/8 inch (10 mm) hole. With insulating washer. Choice of red or black color coding. |
|
|
| Mounts from bottom of chassis. Standard NOS US issue for mounting in a 5/8 inch hole. NOS USA manufacture. You can combine this item with the 7 pin shield to make a 7 pin shielded socket. |
|
|
| 7 pin miniature (British nomenclature B7G) socket for printed circuit board mounting. |
|
|
|
Standard size 9 pin socket for printed circuit board mounting (3/4 to 13/16 inch pin circle diameter), but has base skirt for a standard "j-slot" shield (sold separately, see below). |
|
|
| Standard size for printed circuit board mounting (3/4 to 13/16 inch pin circle diameter), gold plated pins. |
|
|
| Standard size for printed circuit board mounting (3/4 to 13/16 inch pin circle diameter) |
|
|
Fits holes 1 inch to 1-1/8 inch diameter, mounting holes are on 1 1/2" centers. |
|
|
| Fits holes 1 inch to 1-1/8 inch diameter, mounting
holes are on 1 1/2" centers. With separate mounting ring, so may be mounted on top or bottom of chassis. |
|
|
| 77-MIP-8 Octal Amphenol Molded In Plate,new,black plastic with plated brass contacts, mounts in conventional 1 1/8" hole with 1 1/2" mounting centers. Made in USA. |
|
|
| ST70 Dual RCA Input JacksOriginal NOS Dual RCA Input Jack. Replace or restore broken part. Same as Original. |
|
| Triode Electronics Inc.
5633 W. Irving Park Road Chicago IL 60634 USA Ph 773-427-8823 (773-HAS-TUBE) Fax 773-327-5652 Open 10:30 AM to 5 PM CT Monday-Tuesday-Thursday-Friday |