 Here are all the chassis, faceplates and cabinets we carry for your DIY pleasure. ALL CHASSIS & CABINETS ARE MADE IN USA! |
| ||||
 Dynaco Stereo 70 Upgrade Style Punched Chassis MADE IN USANEW ST-70 type Stainless Steel Punched Chassis. Same dimensions as original. Upgrade chassis has cut-outs in front for modern RCA jacks. These are spaced further apart for modern cables. Cut-outs in Back for Binding Posts instead of the original terminal strips make hooking up speaker wires a breeze. These also provide much better contact for the speaker wires. IEC Power Cord Socket Cut-Out on back. Original or repro st70 cages will fit, as on original. Nice stainless steel finish. Check out our custom made Transformers and Boards to build your amp, or you could rebuild your old ST70 on to this New, Improved Chassis. Comes with top and bottom pieces. 13.25" x 9.5" x 1.75" MADE IN USA. | |  NEW Upgraded Dynaco Mk3 Stainless Steel Chassis MADE IN USAStainless Steel, Super Heavy Duty, Punched Chassis for Dynaco Mk3. Same dimensions as original. Has iec power cord cut out, holes for heavy duty binding posts, input jack, and bias point. Also has additional rectifier tube socket cut-out, so you can parallel two together or use a can capacitor in its place. Original or repro Mk3 cages will fit as on original. Nice stainless steel finish. Includes top and bottom. Custom built chassis MADE IN USA. | |  JTM 45 Style Chassis for Tube Amp Kit - MADE IN USAMatching Steel Chassis for our JTM45 Tube Amp Kit! Punched Steel, Room for KT66 tubes, Made in USA. Dimensions 17" x 6.5" x 2.5" high, plus 3/4" wing on each end. |
| ||||
| ||||
 JTM50 / JMP50 / Plexi Style Chassis MADE IN THE USA!Punched steel chassis for our JTM50 & JMP50, and 50w 1987 Plexi Kits. Power transformer cut-out will fit 40-18033 & 40-18054 PT's. Output transformer mounting holes will fit 40-18025 & 40-18039. Dimensions 17" x 6.5" x 2.5" high, plus 3/4" wing on each end. MADE IN USA. | |  FACEPLATE SET FOR JTM45 / JTM50 - MADE IN USAFACEPLATE / BACKPLATE SET FOR JTM45/JTM50 Faceplate and backplate set for JTM45/JTM50 Chassis. Set includes both front and backplate. MADE IN USA. Gold plexi style with black lettering. Measurements: 17” x 2.5” PLEASE NOTE: THERE IS A PROTECTIVE FILM ON TOP THAT NEEDS TO BE REMOVED BEFORE INSTALLATION | |  18W Marshall Style Steel Chassis for DIY TUBE Amp Kit MADE IN USA18W Marshall Style Steel Chassis, Made in USA. A Perfect Match for our 18W TMB Kit!! Dimensions: 6.75" deep by 2.5" high by 19.5" long plus 3/4" wing on each end. |
| ||||
| ||||
 FACEPLATE SET FOR 18W TMB - MADE IN USA18W TMB "Treble, Mid, Bass" Faceplate for 18W Chassis. Set includes both front and backplate. MADE IN USA. IN STOCK NOW! | |  JCM800 2204A 50W Chassis for Version 2 DIY Tube Amp Kit Made in USASteel Chassis for JCM800 2204A VERSION 2 50w Kit. Fits Plexi Style Head Cabinet. (Does not match our Version 1 kit) Accepts Carling Power & Stand-By Switches instead of the Lighted Rocker Switches. Front and Rear Faceplates Now Available!! A Perfect Match for our JCM800 2204A Version 2 Kit!! MADE IN USA. 6.75" deep by 2.5" high by 17" long plus 3/4" wing on each end. | |  JCM800 2203A 100W Chassis for TUBE AMP KIT DIY - MADE IN USAChassis for JCM800 2203A 100W amplifier. Fits Plexi Style Head Cabinet. Accepts Carling Power & Stand-By Switches instead of the Lighted Rocker Switches. Front and Rear Faceplates Now Available!! Dimensions: 25" long (plus a 3/4" wing on each end) x 6.75 deep x 2.5" high. A Perfect Match for our JCM800 2203A Version 2 Kit!! MADE IN USA. |
| ||||
| ||||
 5F1 CHASSIS - CHROME, SCREEN PRINTED, MADE IN USAChromed, screen printed chassis. 8 3/4" x 4 1/8" x 2 5/8" . | |  5E3 CHASSIS - SCREEN PRINTED5E3 CHASSIS - SCREEN PRINTED. 14.5" by 2.5" high, by 4" deep. | | ST70 CHASSIS BOTTOM - MADE IN USA ST70 Chassis Bottom, MADE IN USA. |
| ||||
| ||||
| MK3 CHASSIS BOTTOM PIECE ONLY - MADE IN USA MK3 CHASSIS BOTTOM PIECE ONLY, MADE IN USA. | |  5E3 CHASSIS - MADE IN USA! (BUDGET OPTION 49.95!) NO FACEPLATES LEFTMADE IN USA STEEL CHASSIS Chassis fits our 5E3 kit, the chassis is coated but not chromed/mirror. No printing. NO FACEPLATES LEFT. LIMITED TO SUPPLY ON HAND | | TW Express Style Chassis for our Tube Amp Kit - MADE IN USA - (SEE TW AMP KIT FOR THIS ITEM) TW Express Style Chassis to match our TW Express Style Tube Amp Kit. 17" long x 8" depth by 2" high. Ends are curled under, as opposed to our Marshall style chassis that have the "wings" on the ends. Stainless Steel, MADE IN USA. |
| ||||
| ||||
 5F1 TWEED CABINET - SPECIAL ORDER, PLEASE ALLOW 1-3 WEEKS5F1 TWEED CABINET - SPECIAL ORDER, PLEASE ALLOW 1-3 WEEKS Tweed Deluxe 5F1 Combo Cabinet Beautifully Hand Made Professionally in USA Solid pine with handmade ¼" finger joints, birch baffle board/back panels Dimensions: (H) 13“ x (W) 14 ½“ x (D) 8 ⅞" Chassis Cut-Out 6 ½“ | |  Tweed Deluxe 5E3 Combo Cabinet - SPECIAL ORDER - PLEASE ALLOW UP TO 4 WEEKSTweed Deluxe 5E3 Combo Cabinet - SPECIAL ORDER - PLEASE ALLOW UP TO 4 WEEKS Beautifully Hand Made Professionally in USA Solid pine with handmade ¼" finger joints, birch baffle board/back panels Dimensions: (H) 16" x (W) 20"x (D) 9 ½" Chassis Cut-Out: 12" | |  Hammond Chassis #1444-22The size is 12 X 8 X 2. It is made out of .051 inch aluminum. Great for those DIY projects. Hammond Part # 1444-22. There is a bottom available, sold separately. |
| ||||
| ||||
| HAMMOND CHASSIS BOTTOM FOR 1444-22 HAMMOND CHASSIS BOTTOM FOR 1444-22 Bottom for the Hammond 1444-22 Chassis | |  Hammond 1590J Die Cast EnclosurePerfect for DIY Guitar Effects Pedal Projects! Dimensions: 5.71" (145mm) x 3.74" (95mm) x 1.77" (45mm) | |  Jensen SpeakersTriode is happy to offer Jensen Speakers! |
| ||||
| ||||
 MARSHALL STYLE HEAD CABINET SMALL / 50W - MADE IN USASPECIAL ORDER: PLEASE ALLOW APPROXIMATELY 4-8 WEEKS. MADE IN USA Dimensions: Chassis Cut-Out: 16 3/8" Height 9" x Width 26" x Depth 8 1/4" | |  Marshall Style Large Head Cabinet - MADE IN USAMADE IN USA Dimensions: (Chassis Cut-Out: 16 1/2", Rear Cut-Out: 24 11/16") - (H) 10 3/4" x (W) 29" x (D) 8 1/4" Covering: Marshall Black Levant, Medium Gold Piping, Small Gold Piping Hardware: Gold End Cap Handle, Large Rubber Feet, Gold Metal Mesh SPECIAL ORDER: PLEASE ALLOW APPROXIMATELY 4-8 WEEKS. MADE IN USA. | | Tweed Deluxe 5E3 Combo Cabinet - SPECIAL ORDER - PLEASE ALLOW UP TO 4 WEEKS Tweed Deluxe 5E3 Combo Cabinet - SPECIAL ORDER - PLEASE ALLOW UP TO 4 WEEKS Beautifully Hand Made Professionally in USA Solid pine with handmade ¼" finger joints, birch baffle board/back panels Dimensions: (H) 16" x (W) 20"x (D) 9 ½" Chassis Cut-Out: 12" |
| ||||
| ||||
| 5F1 TWEED CABINET - SPECIAL ORDER, PLEASE ALLOW 1-3 WEEKS 5F1 TWEED CABINET - SPECIAL ORDER, PLEASE ALLOW 1-3 WEEKS Tweed Deluxe 5F1 Combo Cabinet Beautifully Hand Made Professionally in USA Solid pine with handmade ¼" finger joints, birch baffle board/back panels Dimensions: (H) 13“ x (W) 14 ½“ x (D) 8 ⅞" Chassis Cut-Out 6 ½“ | |  St-35 Improved Chassis & BaseDYNACO ST 35i CHASSIS Sold Out... The new ST-35i Chassis and Base is designed to afford better cooling and added space for the under chassis filter choke and capboard. The ST 35i Chassis accepts the power and output transformers from the original Dynaco ST-35, SCA 35 amplifiers, and new Dynaco transformers clones, like ours. In addition, it gives extra spacing for power transformers to run cooler. As an added bonus, the new design is provided with cutouts for Dynaco PC10 (SCA 35) or PC 13 (ST-35) circuit boards. The circuit boards are placed up front and away from the output transformers. The new design allows for improved natural convection air flow so the unit runs cooler. Accepts the original St-35 and SCA 35 power and output transformers as well as PC-10 (SCA 35) and PC-13 (ST-35) circuit boards. An important change to the ST 35i is its overall increased size that allows it to run cooler and increased depth to accommodate a power supply choke. The redesigned ST-35i chassis has been updated to accommodate a mini rocker on/off power switch. Speaker output terminal strips have been removed to allow for the use of 5-way binding posts with 3/4" spacing which accept dual banana plugs. A pair of holes have been provided on the front panel for the insulated RCA input jacks. Precision engineered and manufactured to the same quality standards found in all original Dynaco tube power amplifiers. From the polished nickel finish to the original Dynaco-brown silk-screened lettering, this chassis is pure Dynaco quality. This chassis accepts original ST-70 perforated metal cover. | |  Triode USA DIYTube ST-35 Punched Chassis MADE IN USA -SPECIAL ORDER, MINIMUM QUANTITY 10 PCS REQUIREDA NEW ST-35 type Stainless Steel Punched Chassis for the DIYTube ST-35. Chassis has cut-outs in front for modern RCA jacks. These are spaced further apart to fit modern cables and jacks. Cut-outs in Back for Binding Posts instead of the terminal strips. These provide much better contact for the speaker wires. IEC Power Cord Cut-Out. Nice Super Heavy Duty stainless steel finish. Check out our custom made Transformers and Boards to build your amp. The chassis is punched for the diytube board not the original pc13. Comes with top and bottom pieces. 13.25" x 9.5" x 1.75" MADE IN USA. |
|
Triode, USA Customer Service M-F 9AM-4PM CT 1-800-774-3201 Email us Anytime: questions@triodestore.com |